mirror of
https://github.com/LIV2/GottaGoFaZt3r.git
synced 2025-12-06 00:32:44 +00:00
Add License + Documentation
This commit is contained in:
parent
6ca15ca666
commit
ae81ba2786
92
README.md
92
README.md
@ -1,30 +1,98 @@
|
||||
# GottaGoFastRAMZ3 Fast RAM
|
||||
|
||||
This is an 256MB Autoconfig Fast RAM for the Amiga 3000/4000
|
||||
256MB Autoconfig Fast RAM for the Amiga 3000/4000
|
||||
|
||||
|
||||
|
||||
## Table of contents
|
||||
1. [Status](#status)
|
||||
1. [Features](#features)
|
||||
1. [PCB Ordering](#ordering-pcbs)
|
||||
4. [Jumpers](#jumpers)
|
||||
7. [Bill of materials](#bill-of-materials)
|
||||
2. [Features](#features)
|
||||
3. [Ordering PCBs](#ordering-pcbs)
|
||||
4. [Bill of materials](#bill-of-materials)
|
||||
5. [Troubleshooting](#troubleshooting)
|
||||
6. [Special Thanks and Shoutouts](#special-thanks-and-shoutouts)
|
||||
7. [License](#license)
|
||||
|
||||
## Status
|
||||
|
||||
This is tested and working in a stock Amiga 3000
|
||||
If you have tested this in in another setup (accelerator etc) please let me know by opening an issue on github!
|
||||
|
||||
## Features
|
||||
128MB or 256MB Z3 Fast RAM
|
||||
Brand new 64Mx16 SDRAM chips are quite expensive so the board can also be fitted with 32Mx16 chips for a much lower build cost
|
||||
|
||||
## Ordering PCBs
|
||||
I recommend ordering from JLCPCB as this board was designed within their 4-layer specifications
|
||||
Recommended options when ordering:
|
||||
* Thickness: 1.6mm
|
||||
* Surface Finish: ENIG-RoHS
|
||||
* Gold Fingers: Yes
|
||||
* 45°finger chamfered: Yes
|
||||
|
||||
Layer sequence:
|
||||
|Layer|File|
|
||||
|-|-|
|
||||
|L1|GottaGoFaSDZ3-F_Cu.gbr|
|
||||
|L2|GottaGoFaSDZ3-In1_Cu.gbr|
|
||||
|L3|GottaGoFaSDZ3-In2_Cu.gbr|
|
||||
|L4|GottaGoFaSDZ3-B_Cu.gbr|
|
||||
|
||||
|
||||
## PCB Ordering
|
||||
## Bill of materials
|
||||
|
||||
|Component|Location|QTY|Link|Notes|
|
||||
|---------|--------|---|----|-----|
|
||||
|0.1uF Ceramic Capacitor, 0603|C4-15,C17-44|40|[Mouser](https://www.mouser.com/ProductDetail/80-C603C104K5RAC3121)<br />[DigiKey](https://www.digikey.com/short/f7trtfwt)||
|
||||
|10uF Ceramic Capacitor, 1206|C2-3,C16|3|[Mouser](https://www.mouser.com/ProductDetail/187-CL31A106MAHNNNE)<br />[DigiKey](https://www.digikey.com/short/rqt1br0q)||
|
||||
|33 Ohm Resistor, 0603|R1|1|[Mouser](https://www.mouser.com/ProductDetail/603-RT0603DRE0733RL)<br />[DigiKey](https://www.digikey.com/short/40rdd4m1)||
|
||||
|33 Ohm Resistor network, Convex 1206 (3.2x1.6mm)|RN1-8|8|[Mouser](https://www.mouser.com/ProductDetail/667-EXB-38V330JV)<br />[DigiKey](https://www.digikey.com/short/vhtm8v3440rdd4m1)||
|
||||
|10K Resistor, 0603|R2|1|[Mouser](https://www.mouser.com/ProductDetail/603-RT0603FRD0710KL)<br />[DigiKey](https://www.digikey.com/short/nvvrt5dw)||
|
||||
|LM1117-3.3 SOT-223|U1|1|[Mouser](https://www.mouser.com/ProductDetail/926-LM1117IMP3.3NOPB)<br />[Digikey](https://www.digikey.se/short/jprv7r4q)||
|
||||
|74LVC245N TSSOP|U2-5|4|[Mouser](https://www.mouser.com/ProductDetail/595-SN74LVC245APWT)<br />[DigiKey](https://www.digikey.com/short/pnq3wff3)|Can be substituted with SN74LVTH245 or SN74LVCR2245|
|
||||
|AS4C32M16SC 32Mx16 SDRAM, TSSOP-54|U7-10|4|[Mouser](https://www.mouser.com/ProductDetail/913-AS4C32M16SC-7TIN)<br />[DigiKey](https://www.digikey.com/short/wfwn8nmw)|Cheaper option is to use [A3V56S40GTP](https://www.mouser.com/ProductDetail/155-A3V56S40GTP-60) for a 128MB configuration at a drastically lower price, or scavenge some 32Mx16 SDRAM from old SODIMMs*|
|
||||
|Xilinx XC95144XL-10TQG100C 10ns 144 Macrocell CPLD|U6|1|[Mouser](https://www.mouser.com/ProductDetail/217-95144XL-10TQ100C)<br />[Digkey](https://www.digikey.com/short/w0r0j288)||
|
||||
|Clock Oscillator, HCMOS, 7x5mm, 3.3V, ~66MHz|X1|1|[Mouser](https://www.mouser.com/ProductDetail/959-SM7745HEV-66.667)<br />[DigiKey](https://www.digikey.com/short/q8bzfwj4)|Anything close to 66MHz should work<br />Tested at 66.6666MHz|
|
||||
|
||||
## Jumpers
|
||||
__*__ I cannot provide technical support for RAM chips other than those explicitly listed in the BOM, others may work but you're on your own
|
||||
|
||||
## Troubleshooting
|
||||
__Problem:__ The board is detected but there is less memory detected than there should be. or you see a message stating that the board is "Defective"
|
||||
__Resolution:__
|
||||
1. Check all soldering looking for bad connections and shorts around the RAM and CPLD
|
||||
2. Test the RAM using [ATK](https://github.com/keirf/amiga-stuff/releases)
|
||||
Look for the relevant region under "List and test regions" and test it
|
||||
Consult the memory layout to determine which IC is responsible for any stuck bits you might see
|
||||
|
||||
### Bill of materials
|
||||
### Memory Layout
|
||||
The memory is laid out in a way that causes it to wrap around above 128MB when only 128MB of ram is fitted to the card allowing either 128/256MB configuration with the same CPLD firmware.
|
||||
Kickstart will notice this wrap and add only 128MB to the free pool in this instance.
|
||||
|
||||
|Component|Location|QTY|Link|
|
||||
|---------|--------|---|------|
|
||||
|||||
|
||||
|Address|D0-15|D16-31|
|
||||
|-------|-----|------|
|
||||
|40000000-43FFFFFF|U7|U9|
|
||||
|44000000-47FFFFFF|U8|U10|
|
||||
|48000000-4BFFFFFF|U7|U9|
|
||||
|4C000000-4FFFFFFF|U8|U10|
|
||||
|
||||
## Special Thanks and Shoutouts
|
||||
* [Niklas Ekström](https://github.com/niklasekstrom) for helping to clean up my messy code
|
||||
* [GadgetUK164](https://www.youtube.com/gadgetuk164) for ~~being a guinea pig~~ beta testing many of my boards
|
||||
* SparxUK also for being a helpful beta tester of many of my boards
|
||||
* [CDH](https://github.com/cdhooper) and [Stefan Reinauer](https://github.com/reinauer) for helping me to get my A3000 going
|
||||
* [Rob "peepo" Taylor](https://tindie.com/stores/bobsbits/) whose A500++ got me started on my journey of tinkering with Amigas
|
||||
* [jbilander](https://github.com/jbilander)
|
||||
* RetroFletch
|
||||
* [SukkoPera](https://github.com/SukkoPera)
|
||||
|
||||
## License
|
||||
|
||||
[![CC BY-SA 4.0][cc-by-sa-shield]][cc-by-sa]
|
||||
|
||||
This work is licensed under a
|
||||
[Creative Commons Attribution-ShareAlike 4.0 International License][cc-by-sa].
|
||||
|
||||
[![CC BY-SA 4.0][cc-by-sa-image]][cc-by-sa]
|
||||
|
||||
[cc-by-sa]: http://creativecommons.org/licenses/by-sa/4.0/
|
||||
[cc-by-sa-image]: https://licensebuttons.net/l/by-sa/4.0/88x31.png
|
||||
[cc-by-sa-shield]: https://img.shields.io/badge/License-CC%20BY--SA%204.0-lightgrey.svg
|
||||
@ -1,3 +1,14 @@
|
||||
/*
|
||||
GottaGoFaZt3r
|
||||
Copyright 2022 Matthew Harlum
|
||||
|
||||
GottaGoFaZt3r is licensed under a
|
||||
Creative Commons Attribution-ShareAlike 4.0 International License.
|
||||
|
||||
You should have received a copy of the license along with this
|
||||
work. If not, see <http://creativecommons.org/licenses/by-sa/4.0/>.
|
||||
*/
|
||||
|
||||
module Autoconfig (
|
||||
input match,
|
||||
output reg [3:0] addr_match,
|
||||
|
||||
12
RTL/sdram.v
12
RTL/sdram.v
@ -1,4 +1,14 @@
|
||||
`timescale 1ns / 1ps
|
||||
/*
|
||||
GottaGoFaZt3r
|
||||
Copyright 2022 Matthew Harlum
|
||||
|
||||
GottaGoFaZt3r is licensed under a
|
||||
Creative Commons Attribution-ShareAlike 4.0 International License.
|
||||
|
||||
You should have received a copy of the license along with this
|
||||
work. If not, see <http://creativecommons.org/licenses/by-sa/4.0/>.
|
||||
*/
|
||||
`timescale 1ns / 1ps
|
||||
|
||||
module SDRAM(
|
||||
input [27:2] ADDR,
|
||||
|
||||
11
RTL/top.v
11
RTL/top.v
@ -1,3 +1,14 @@
|
||||
/*
|
||||
GottaGoFaZt3r
|
||||
Copyright 2022 Matthew Harlum
|
||||
|
||||
GottaGoFaZt3r is licensed under a
|
||||
Creative Commons Attribution-ShareAlike 4.0 International License.
|
||||
|
||||
You should have received a copy of the license along with this
|
||||
work. If not, see <http://creativecommons.org/licenses/by-sa/4.0/>.
|
||||
*/
|
||||
|
||||
module GottaGoFaZt3r(
|
||||
input [27:2] A,
|
||||
inout [31:28] AD,
|
||||
|
||||
Loading…
x
Reference in New Issue
Block a user