pistorm/amiga.cfg

# Sets CPU type. Valid types are (probably) 68000, 68010, 68020, 68EC020, 68030, 68EC030, 68040, 68EC040, 68LC040 and some STTTT thing.
cpu 68020
# Map 512KB kickstart ROM to default offset.
map type=rom address=0xF80000 size=0x80000 file=kick.rom ovl=0 id=kickstart
# Comment out the line above and uncomment the line below to automatically copy the ROM contents to Pi RAM if the file isn't found
#map type=rom address=0xF80000 size=0x80000 file=kick.rom ovl=0 id=kickstart autodump_mem

# "Blackhole" the detected slow RAM on the Amiga 600. This enables maprom to work without using specifically kick v40.63
# DO NOT ENABLE THIS UNLESS YOU ARE USING THE PISTORM ON AN AMIGA 600.
#map type=register address=0xC00000 size=0x80000 id=blackhole_slow_a600

# Want to map an extended ROM, such as CDTV or CD32?
#map type=rom address=0xF00000 size=0x80000 file=cdtv.rom id=extended

# Map 128MB of Fast RAM at 0x8000000, also known as 32-bit Fast RAM or CPU local Fast RAM.
# Only supported properly on select Kickstarts, such as 3.1+ for Amiga 1200, 3000 and 4000.
#map type=ram address=0x08000000 size=128M id=cpu_slot_ram
# Map 128MB of Z3 Fast. Note that the address here is not actually used, as it gets auto-assigned by Kickstart itself.
# Enabling Z3 fast requires at least Kickstart 2.0.
# If for some reason you need more than 128MB, you can change the size=128M to a valid supported Z3 PIC size,
# like 256M, 512M, 1024M, or add additional map lines.
map type=ram address=0x10000000 size=128M id=z3_autoconf_fast
# Max 8MB of Z2 Fast can be mapped due to addressing space limitations, but for instance 2+4MB can be chained to leave 2MB for something else.
# Do not map Zorro II Fast RAM unless you absolutely need it, as Z2 address space is very limited.
# Cases where you may need Zorro II Fast may include emulating a 68000, 68010 or 68EC020, and/or if you are using Kickstart 1.3.
#map type=ram address=0x200000 size=8M id=z2_autoconf_fast
#map type=ram address=0x200000 size=2M id=z2_autoconf_fast
#map type=ram address=0x400000 size=4M id=z2_autoconf_fast

# This is fake Chip RAM, do not use on a real Amiga.
#map type=ram address=0x0 size=2M

# Map Gayle as a register range.
# NOTE: Gayle emulation is currently non-functional. Do not enable this.
#map type=register address=0xD80000 size=0x40000
# Map RTC as a register range.
map type=register address=0xDC0000 size=0x10000
# Number of instructions to run every main loop.
loopcycles 300
# Set the platform to Amiga to enable all the registers and stuff.
platform amiga
# Uncommenting the below this long comment DISABLES RTC emulation, letting reads/writes through to the RTC memory range.
# There is no need to uncomment it unless you are either using a CDTV, you want to use a physical RTC source present
# inside the computer, such as on a trapdoor memory expansion board, or if you have a physical A314 intalled, since the
# A314 uses the RTC address range to communicate with the Amiga, and enabling RTC emulation # blocks this communication completely.
# DO NOT UNCOMMENT THE LINE BELOW UNLESS YOU'VE READ AND UNDERSTOOD THE FIVE LINES ABOVE THIS ONE.
#setvar enable_rtc_emulation 0
# Uncomment to enable RTG
#setvar rtg
# Uncomment to enable DPMS (monitor turns off) when RTG sleeps
#setvar rtg-dpms

# Uncommenting the lines below here sets the specified sample rate for the Pistorm AHI device and enables the PiStorm AHI
# device respectively. The PiStorm AHI device does not yet work properly, please read the information in the readme file
# located in the directory platforms/amiga/ahi.
#setvar pi-ahi-samplerate 44100
#setvar pi-ahi

# Uncomment to enable CDTV mode (not working, requires Kickstart 1.3+CDTV extended ROM)
#setvar cdtv
# Uncomment this line to enable the PiSCSI interface
#setvar piscsi
# Use setvar piscsi0 through piscsi6 to add up to seven mapped drives to the interface.
#setvar piscsi0 PI0.hdf
#setvar piscsi1 PI1.hdf
# A special disk that includes PiStorm drivers and utilities, comment out if not needed
setvar piscsi6 platforms/amiga/pistorm.hdf
# Uncomment this line to enable the (currently non-working) Pi-Net interface.
#setvar pi-net

# Uncomment and edit to set a custom config filename for the A314 emulation
#setvar a314_conf ./a314/files_pi/a314d.conf
# Uncomment to enable A314 emulation
#setvar a314

# Please take note:
# At the time of writing this (22 Jun 2021), the mouse and keyboard forwarding (for Amiga only) is by no means perfect.
# It works properly in Workbench, and in a number of games and applications, but it does not work for everything.
# Do not rely on the mouse and keyboard forwarding as your only means of input for the host computer.

# Forward keyboard events to host system, defaults to off unless toggle key is pressed, toggled off using F12.
# Syntax: keyboard [grab key] [grab|nograb] [autoconnect|noautoconnect]
#   "grab" steals the keyboard from the Pi so Amiga/etc. input is not sent to the Pi
#   (also helps prevent sending any ctrl-alt-del to the Amiga from resetting the Pi)
#
#   "autoconnect" connects the keyboard to the Amiga/etc. on startup
keyboard k nograb noautoconnect
# Select a specific filename for the keyboard event source.
# This is typically /dev/input/event1 or event0, but it may be event3 with for instance a wireless keyboard.
# Use ls /dev/input/event* to check which event files are available and try until you find the one that works.
#kbfile /dev/input/event1
# Forward mouse events to host system, defaults to off unless toggle key is pressed on the Pi.
# Syntax is mouse [device] [toggle key] [autoconnect|noautoconnect]
# (see "keyboard" above for autoconnect description)
mouse /dev/input/mice m noautoconnect

# Uncommenting below moves slow ram to the chip ram giving 1MB of chip ram
# NOTE: Requires a 1MB ECS Agnus (8372) and a trapdoor memory expansion!
#setvar move-slow-to-chip

# Swap DF0 with DF1/2/3 - Useful for Kickstart 1.x / Trackloader games that will only boot from DF0
#setvar swap-df0-df 1